Home > Bolt Dress Kits > Domestic Vehicle Bolt Dress Kits > LX: Dodge/Chrysler (2005-Current) (300, Challenger, Charger, Magnum etc) > LX Gen 1: Dodge/ Chrysler (2005-2010) > Engine Dress Kits (LX 2005-2010)
Sort By:
Page of 2
LX Firewall Panel-to-Cross Strut Bar Dress Kit LX Intake Bracket Bolt (1st Gen, 2nd Gen, 3rd Gen) LX Positive Battery Terminal Spike Kit
Do you have a firewall cover attached to your cross strut bar/strut bar with some self-tapping screws? Upgrade to the West Coast Fasteners solution with actual nutserts, bolts, and washers.

The following comes with the kit:

-4 or 6 Bolts;
-4 or 6 Washers;
-4 or 6 Nutserts; and
-4 or 6 anti-scratch gaskets.
A lot Chrylser/Dodge customers run some sort of aftermarket intake box and are left with the lonesome OEM bolt that sits on the intake bracket/Radiator Support that is a total eye sore. This dress kit replaces the less than desirable OEM bolt with an allen bolt and tapered aluminum washer.

The following comes with the kit:
-1 bolt *
-1 washer

*The supplied bolt from us is shortened for improved fitment and unnecessary length that the factory bolt provides.

Did your positive battery terminal cover cap break on you? West Coast Fasteners knows that this is a common issue and decided to offer a simple solution for a different twist.

The kit comes with the following:

-1 Spike *
-1 Washer

*2011 Plus you may have to trim down the positive terminal thread post slightly to allow the spike to thread down all the way.
LX Positive Terminal Cover with Titanium Nut Option Billet Technology Z-Bracket Hardware Upgrade LX AC Line Spikes
LX AC Line Spikes
Our Price: $20.00
Has your battery terminal cover cap break on you leaving a huge eye sore? You can now replace it with this terminal cover that comes pre-trimmed to fit 1st Gen LX's (2005-2010)***, or if uncut will fit 2nd and 3rd gens as well (2006-current).

West Coast Fasteners takes it a step further and we offer a titanium nut option to replace the aged looking OEM piece.

***The positive terminal cover itself is not offered by Dodge as a direct replacement for 1st gens. We have been told that Dodge sells the entire terminal cover as a complete set with the harness as well as the actual positive terminal post that is either discontinued or costs so much that dealers started offering this solution as an economical option.

There will be a slight difference in the overall fit and finish, but once trimmed it will work for 1st gen LX's.
The cover may require minor shifting or use of a washer may be necessary.
The West Coast Fasteners Z-bracket dress kit upgrades the exposed hex head bolt to a nice stainless steel bolt with a tapered washer. We also replace the black oxide bolt on the top of the Z bracket with a stainless steel or titanium bolt.

The kit comes with the following:

-2 Bolts
-1 Washer

*The Oil Catch Can and bracket are sold separately.


The AC line spikes add a little extra to a rather boring part of the LX engine bay.  The spikes thread right over the factory nuts and add a little style.  The picture used for this item has West Coast Fasteners Titanium Nuts installed underneath the spikes.
(LX/WK) Heater Pipe and Cam Position Sensor Dress Kit PCM to Cross Strut bar Bracket (LX 2005-2010) LX Hood Striker Bolt Dress Kit (Bolts Only)
Fitment for: 2005 to current model LX.

1st gen these locations are very exposed. 2nd and 3rd gen is not as prominent.

There are 2 bolts that attach the PCM computer to the bracket that holds down the PCM to the OEM cross strut bar or aftermarket strut bar. West Coast Fasteners made a kit for this piece since the hardware shows through the front "pizza shaped" section of the cowl.

The dress kit comes with the following:

2 Bolts
2 Washers

This kit replaces the hideous OEM hardware for the hood striker. The following comes with the kit:

-2 Washers*
-2 Anti-Scratch gaskets*
-2 Bolts*

*Hood striker is sold separately.
LX Coolant Tank 2005 - Current LX EGR Delete Dress Kit 5.7 Hemi (Bolts Only) No Plate Windshield Squirter / Hood Nozzle Hose Delete Hardware

The coolant tank dress kit is pretty self explanatory. People spend so much time painting, hydropipping, and even fiberglassing them for a different shape. However, all of that work doesn't come full circle until you match it with some beautiful hardware.

The coolant dress kit covers the following:

  1. 2 Bolts ***
  2. 2 Washers
***The coolant tank threading is known to be stubborn at times, don't be alarmed as we have matched the thread pitch as close as we could to make the install as easy as possible. If extremely necessary, it may require a tap to clear the way.
The Billet Technology EGR block off plate that attaches to the passenger side head is a beautiful billet aluminum piece, but it looks a lot better with the West Coast Fasteners Bolt Dress Kit that is being sold in this listing.

The EGR delete comes with the following:

-2 Bolts
-2 Washers
***EGR Block-off Plate is NOT included and sold separately by a few different vendors.

All hardware is strictly for off-road use only* West Coast Fasteners always advises to use the proper torque specs when installing your hardware and recommends referencing your factory manuals for reference.*

For those that have shaved their Hood nozzles or did away with their hood/headlight squirter lines, West Coast Fasteners created a hose delete kit to clean it up. Once the hoses are deleted from the passenger side fender, there are two visible holes that are a real eye sore. We made this kit to delete the holes in style.

The dress kit comes with the following items:

-2 Bolts
-2 Washers
-Nut kit*** Must be mechanically inclined to install
LX J-Hook Front Cowl Delete Kit LX Strut Spike Kit (1 Pair Only) Hemi Water Neck Dress Kit
Hemi Water Neck Dress Kit
Our Price: $28.00
West Coast Fasteners (WCF) has found a solution to delete the OEM J-Hooks on the far left and right side of the front cowl on your LX! The infamous J-Hooks are not only expensive to replace, but also turn grey or white over time.

The J-hooks don't really serve much of a purpose especially if you have already upgraded your factory front cowl kit to the WCF version.

After many requests, West Coast Fasteners is now offering the LX Strut Spike kit! It replaces the factory strut nut part number: 06506152aa. If you are running aftermarket suspension, please make sure that the nuts your suspension are using are the OEM part number listed above or a M8x1.25 thread pitch.***

The entire length of the spike is approximately 1 inch in length so check for clearance on any aftermarket strut bar you may be using. It also has approximately 9/16" of thread length.

The LX strut spike kit comes with the following:

  1. 2 Strut Spiked Nuts (Must purchase 3 pairs to cover all 6 strut nuts)
  2. 2 Anodized Washers (Must purchase 3 pairs to cover all 6 strut nuts)
***We only have special fitment for customers with UAS Airbag suspension, which is an available option in one of the dropdown menus above. Other than that, all of the rest follow the factory thread pitch listed above.

******
Our Water Neck Bolt Dress Kit is fully exposed on Hemi engines and is a great compliment to the Billet Technology Water Neck. The bolt dress kit also fits OEM applications as well.

[The dress kit comes with the following]:

-2 Bolts*
-2 Washers*

*The actual Billet Technology water neck is NOT included and is shown in the photo for display purposes only.


LX ABS Block and Impact Sensors Dress Kit LX/WK Idler Pulley Dress Kit Billet Technology Coil Pack Dress Kit (Bolts Only)

This Dress kit replaces the single bolt exposed next to the ABS and the 4 bolts (2 per side) on the Impact sensors***that run next to the front headlights and radiator fans/shroud.

The following is included:

-5 Bolts
-5 Washers

***Do not disconnect the harness of the impact sensors. Just swap the bolts.

The idler pulley hardware is a commonly overlooked piece, but is clearly in the open and looks amazing once the West Coast Fasteners Dress kit is installed.

The following hardware comes with the kit:

- 2 Bolts
- 2 Washers

The West Coast Fasteners BT Coil Pack Cover dress kit replaces the standard hex head bolts, with upgraded washers and bolts!

The dress kit comes with the following:

-4 Bolts*
-4 Washers

The Billet Technology Coil Pack Covers are NOT INCLUDED and are sold separately.

This dress kit is for Hemi equipped vehicles.
LX Radiator Panel Bolt Dress Kit LX Ground Spike Kit (LX/WK) Head Bolts Dress Kit
LX Ground Spike Kit
Our Price: $35.00

West Coast Fasteners is now offering an option besides those self tapping screws that typically come with radiator panels from 3GKustomz, Trufiber, etc.

The dress kit includes:

  1. 4 Bolts
  2. 4 Washers
  3. 4 Anti-scratch Gaskets
  4. 4 Nutserts ***
  5. Nutsert Tool (Optional) **

***Nutserts must be installed with a nutsert tool.

**The "Grade B" Nutsert Tool comes bare bones with 2 installation adapters which will work with the Mopar related kits and will get the job done. The "Grade A" comes with 4 installation adapters that will cover you for other potential installations along with a tool case, but is not required to complete install.



A solution is finally here to cover up the ground bolts that not only stick out like a sore thumb, but also usually reveal a less than appealing ground nut that is either rusted or chipping. The spikes have a thread capacity of approximately 1/2" and a total length of approximately 1.2".*

  1. 1st gen = 4 Ground Spikes
  2. 2nd Gen = 6 Ground Spikes
  3. 3rd Gen = 6 Ground Spikes

These are an often overlooked piece considering they stick out like a sore thumb! These black bolts are located right next to the valve cover bolts at the top (front and rear).

The following is included:

-4 Bolts
-4 Washers

Picture shows the front passenger side head bolt and BT z-Bracket bolt being upgraded with West Coast Fasteners hardware.

Hemi Power Steering Pump Dress Kit LX/WK Hemi Fuel Rail Bolt Dress Kit LX Top Front Bumper Dress Kit (1st Gen)
West Coast Fasteners dug deep in to the Hemi engine and figured out a way to truly pimp out a power steering pump. The power steering pump kit replaces the hardware that mounts the power steering pump to the engine.

The following comes with the dress kit:

-3 Bolts***
-3 Washers***

***Photo was for demo purposes to show the 4 rear bolts (that cannon be seen once installed & the 1 bolt that holds the neck on to the pump)
West Coast Fasteners offers both this regular duel rail dress kit as well as our spiked edition.

The following comes with this specific kit:

-4 Bolts*
-4 Washers (Tapered style)
*NO FUEL RAILS INCLUDED.

*Burnt titanium only offered for 1st Gens.

The Top Front Bumper Dress Kit replaces the 4 (or 6 for Magnum and Charger) factory clips that sit on top of the front bumper.. The OEM clips are notorious for breaking all of the time and look bad over time. Upgrade to our all metal hardware and be done with it once and for all.

The following comes with the kit:

-4 Washers (8 for Dodge Charger and Magnum)
-4 Bolts (8 for Dodge Charger and Magnum)
-Nut Kit***

Hemi Throttle Body Dress Kit LX / WK Hemi HHP Metal Power Steering Pulley Dress Kit LX Headlight Dress Kit
LX Headlight Dress Kit
Our Price: $45.00

The Throttle Body and Intake Bracket dress kit cleans up the nose of the engine nicely.

This throttle body kit covers the following:

  1. 4 Bolts *****(Titanium upgrade option is ONLY available for 1st Gen 2005-2010 and Hellcat Engine)*****
  2. 4 Washers

Washer Colors Available: Aluminum, Black, Blue, Gold, Purple, Red, and Orange

The optional Allen key is provided just as an aid during install. A torque wrench is recommended for final tightening with factory torque specs.
Did you already do yourself a favor and upgrade your cheap plastic power steering pulley to the metal version by HHP? West Coast Fasteners went ahead and decked this unit out as well.

The dress kit comes with the following:

-6 Bolts
-6 Washers
The following comes with the kit:

-6 Bolts
-6 Washers
LX Procharger Version 2 Bracket Dress Kit Hardware Billet Tech UniStrut Dress Kit (Hardware Only) Mopar Cold Air Intake Dress Kit (2005-2015 LX)
This dress kit covers replaces the hardware found on Mr. Austin Lones' Procharger Bracket for the Hemi platform. Prevent belt slip and belts being thrown on your Procharger Supercharger.

The dress kit comes with the following:

-3 Bolts (Reuse the original pulley bolt)
-4 Anodized Washers

*The kit does NOT include the actual bracket that is sold separately.
Do you have the Billet Technology UniStruts and would like to add a little personal touch? West Coast Fasteners has an anodized washer upgrade in the following colors:

Silver, Black, Red, Blue, Purple, Gold, and Orange

The following is included in the dress kit:

-6 Aluminum Washers (Only 3 are needed for Hellcats)*

*To complete the Hellcat look, West Coast Fasteners recommends the Coolant Tank Secondary Reservoir kit that contains 3 Titanium Nuts and 3 Washers.
Own the awesome Mopar CAI, but tired of looking at the boring hardware that it comes with? West Coast Fasteners has this dress kit that will include the following:

-5 Bolts
-5 Washers

*The actual intake is not included.

The hardware replaces the (1) intake bracket bolt and the 4 bolts that attach the heat shield to the intake filter/heat shield to the intake pipe.