Home > Clamps / Braided Hose / Fittings
Sort By:
Page of 1
Titanium Hose/Piping Clamp SS T-Bolt Clamps with a Burnt Classic Finish Titanium Look Aluminum Hose Clamp w/ Titanium Hardware
[All sales are Bespoke/Custom and are FINAL. Once the order is placed, you have 24 hours to cancel since the funds will be used for setup and material. By placing your order, you agree to these terms and conditions.]

MARINE GRADE AND PROUDLY MADE IN THE USA!

ADJUSTABLE TITANIUM HOSE CLAMPS! STRONGER THAN STAINLESS STEEL, LIGHTWEIGHT AND CORROSION RESISTANT!

Titanium hose clamps feature a high strength (1/2 inch wide band) specifically engineered to allow for the highest torque rating possible. The rolled/flared edge of the band allows for smooth installation of the clamp and also prevents chaffing or tearing of the hose when tightening. The housing is the thickest possible to ensure stability of the screw during operation.

Hose Clamp Specifications:
• 100% Titanium construction. Screw, Housing, and Band.
• Screw head accepts: Phillips Head screwdriver, Flat Head screwdriver, Socket or wrench.
• Hi-Torque screw to reduce binding and galling.
• ½ inch wide Hi-Strength, flexible design band.
• Rolled/Flared band edges to prevent chaffing or tearing of hoses.
• Thick High-Stability Screw Housing to enhance performance and screw stability.

Color Options:
-Silver
-Burnt Classic- Half burns with mixes of it on the bolt area and clamp (Shown in photo).
-Burnt Blue- Heavy blue burns throughout the clamp body with possible color variation due to the design of the item.
-Burnt Purple- Heavy purple burns throughout the clamp body with possible color variation due to the design of the item.
-Burnt Bronze-Heavy bronze burns throughout the entire bolt and body with possible color variation due to the design of the item.

Standard to Metric Diameter Guide (Approximate Measurements):

•7/16 inch -11/16 inch (~11 mm - 17.50 mm)
•5/8 inch -15/16 inch (~16 mm - 23.81 mm)
•7/8 inch - 1*1/4 inch (~22.23 mm - 31.75 mm)
•1*1/16 inch - 1*1/2 inch (~27 mm - 38.1 mm)
•1 inch - 2 inch (~25.4 mm - 50.8 mm)
•1*1/2 inch - 2*1/2 inch (~38.1 mm - 63.5 mm)
•2*3/4 inch - 3*3/4 inch (~69.85 mm - 95.25 mm)
•3*1/2 inch - 4*1/4 inch (~88.90 mm - 108.00 mm)
•4 inch - 5*1/2 inch (~101.60 mm - 139.70 mm)
•4*1/2 inch - 6 inch (~114.30 mm - 152.40 mm)
•5.375 inch - 6.5 inch (~136.50 mm - 165.1 mm)

This is merely a guide. Make sure to measure the outer diameter of where the clamp is installed and match the clamps being purchased up with your current setup.

[Disclaimer]: ALL Orders are Bespoke, Custom Orders and Returns and Refunds are not available.
[All sales are Bespoke/Custom and are FINAL. Once the order is placed, you have 24 hours to cancel since the funds will be used for setup and material. By placing your order, you agree to these terms and conditions.]

THESE ARE NOT TITANIUM
.
ADJUSTABLE T-BOLT HOSE CLAMPS WITH A "BURNT CLASSIC FINISH" LOOK!

Hose Clamp Specifications:
• 100% Stainless Steel construction. Screw, Housing, and Band.
• Screw head accepts: Socket or wrench.
• Hi-Torque screw to reduce binding and galling.
• Rolled/Flared band edges to prevent chaffing or tearing of hoses.
• Thick High-Stability Screw Housing to enhance performance and screw stability.

Color Options:

-Burnt Classic- Half burns with mixes of it on the bolt area and clamp (Shown in photo).

Standard to metric diameter guide for recommended fitment (Clamps may vary by a few mm from the guide below and the drop down menu):

-1.75 inch (45 mm - 53 mm)
-2.00 inch (57 mm - 63mm)

-2.25 inch (59 mm - 67 mm)
-2.5 inch (65 mm - 73 mm)
-2.75 inch (72 mm - 80 mm)
-3.00 inch (78 mm - 86 mm)
-3.25 inch (84 mm - 92 mm)

-3.50 inch (90 mm - 98 mm)
-3.75 inch (97mm -105 mm

THESE ARE NOT TITANIUM.

[All sales are Bespoke/Custom and are FINAL. Once the order is placed, you have 24 hours to cancel since the funds will be used for setup and material. By placing your order, you agree to these terms and conditions.]

[The following come with each order]:

-1 Aluminum Clamp
-1 Titanium Bolt

Sizing Guide: ***

The clamp fully closes at a slightly higher number than the recommended piping size to accommodate the silicone couplers/connectors.

-1.65 Inch (~41.91 mm) piping outer diameter; [Clamp fully closes @ approximately 1.65 inch (~41.91 mm)].
-2.00 Inch (~50.8 mm) piping outer diameter; [Clamp fully closes @ approximately 2.25 inch (~57.15 mm)].
-2.25 Inch (~57.15 mm) piping outer diameter; [Clamp fully closes @ approximately 2.50 inch (~63.50 mm)].
-2.50 Inch (~63.50 mm) piping outer diameter; [Clamp fully closes @ approximately 2.75 inch (~69.85 mm)].
-2.75 Inch (~69.85 mm) piping outer diameter; [Clamp fully closes @ approximately 3.00 inch (~76.20 mm)].
-3.00 Inch (~76.20 mm) piping outer diameter; [Clamp fully closes @ approximately 3.25 inch (~82.55 mm)].
-3.25 Inch (~82.55 mm) piping outer diameter; [Clamp fully closes @ approximately 3.50 inch (~88.90 mm)].
-3.50 Inch (~88.90 mm) piping outer diameter; [Clamp fully closes @ approximately 3.75 inch (~95.25 mm)].

***The recommended sizing is based on the diameter of the silicone hose/hose ends that the clamp is being used on. Some hose brands may vary in overall fitment.

West Coast Intake Box / Tube Breather Hose & Fittings Billet Technology (BT) Oil Catch Can Fittings (Only) BT Signature Series Overflow Catch Can Braided Hose and Fittings
West Coast Fasteners is offering an upgraded braided hose and fitting kit for the cold air intake tube and your engine. Simply measure the existing hose from your engine and intake tube and select the length in the dropdown box accordingly. ***


***The braided line and fittings will ONLY work with aftermarket intakes that still use a breather hose.


Vehicle Fitment:

  • Dodge Challenger (5.7L, 6.1L): 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
  • Dodge Charger (5.7L, 6.1L): 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
  • Dodge Magnum (5.7L, 6.1L): 2005, 2006, 2007, 2008
  • Chrysler 300 (5.7L, 6.1L): 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
  • Jeep Grand Cherokee (6.1L, 6.4L): 2006, 2007, 2008, 2009, 2010, 2012, 2013, 2014, 2015
Do you already have braided hose for your Billet Technology Oil Catch Can and just want the fittings? The following comes with this purchase:

-Alumiunum Hose Ends (Quantity 4)

Colors Available: Satin, Black, Red, Blue & Chrome


Complete your Billet Technology Signature Series Overflow Catch Can kit by upgrading to braided hose and fittings to the West Coast Fasteners kit. We also have kits for the famous BT Oil Catch can, and coolant tank.

The following comes with the kit:
-Braided Hose
-Hose Fittings (Quantity 4)

The photo is to demonstrate which BT product works with this hose and fitting package and must be purchased separately in the Billet Technology section of the website.


Jeep Grand Cherokee WK1 Coolant Tank Braided Hose Kit West Coast Braided Hose & Fittings for Coolant Tank Lines (2.7/3.5/5.7/6.1) West Coast Fasteners Engine Harness Sleeve Kit w/ Tie Straps
Replace the rubber hose that runs from the coolant tank reservoir on the passenger side of the Jeep WK1 to the radiator.

The following comes with the kit:
-2 Fittings
-Braided Hose (pre-cut)

The display picture also shows a Billet Technology Radiator Cap that is not included with purchase and is just for display purposes only.

The West Coast Fasteners coolant tank line kit comes with the following items:

-1 Coolant Tank rear line
-1 Coolant Tank overflow line
-3 Fittings

Coolant Tank Rear Line

Fitment for the following: 2005-2007 Chrysler 300, Dodge Charger, and Magnum

Modification required: 2008 and up Chrysler 300, Dodge Challenger, and Charger requires cutting of the stock line and use of a 3/8" by 3/8" male hose barb that is not included, but can be found at your local hardware store.



Is your engine harness starting to look bad and could use a refresh on protection to prevent shorts and rubbing wires? Are you tired of looking at the generic wire loom that comes from the factory?


West Coast Fasteners now offers a solution that will truly clean up that engine bay. We offer optional pre-cut tie straps, but also provide just the sleeving for those that would prefer to use heat wrap.


The sleeving covers the following:

-Main engine harness running from behind the valve covers through the manifold to the front of the engine
-Coil pack wiring
-Injector wiring
-Throttle Body
-IAT Sensor
-Cam position sensor
-Alternator
-Harness that runs along the top of the radiator shroud

Fitment for the following vehicles:

Hemi Engines 2005-2010 Chrysler 300, Dodge Charger, Dodge magnum, Dodge Challenger

BT Oil Catch Can Braided Hose and Fittings (Jeep, Ram, Durango) BT Oil Catch Can Braided Hose and Fittings (Mopar V6/V8 Hemi LX Kits)

Do you have a Billet Technology catch can, but would like a different look or upgrade from the rubber hoses you have now? Then this is the perfect option for your ride.

This item includes the following:
-Braided Hose
-Fittings (Quantity 4)

We also carry the Billet Technology Catch can, which can also be added to your shopping cart by going to the Billet Technology Hardware section of our website.

***This item does not include the actual oil catch can itself as that has to be purchased separately.

Do you have a Billet Technology catch can, but would like a different look or upgrade from the rubber hoses you have now? Then this is the perfect upgrade for your ride.

The Billet Technology Catch can be purchased directly by going to the BT website.***

[The following is included]:
-braided hose
-hose ends/fittings (Qty 4)
(Actual Oil Catch Can must be purchased separately)

***This item DOES NOT include the actual oil catch can itself as that has to be purchased separately.